Embedded Systems with 8051 Micro Controller using Embedded C by Amit Rana

Embedded Systems with 8051 Micro Controller using Embedded C


Deep Dive into embedded systems with in-depth understanding of 8051 micro controller with embedded C programming

Kitflix Supports learners in a unique way

When you buy course from Kitflix.com, you're entitled to
  • Lifetime support over email
  • Lifetime support and consultation over phone
  • Direct contact over whatsapp
  • One on One session on Request
  • Remote Desktop Asssistance on Request
Enroll at much lower price without support here on udemy
Enroll on Udemy at Low Price

Personalize One To One Support

This is not just a course but you will also get personalize  one to one email support over all your queries and doubts for life

Learn Embedded Systems with one of the most influential and basic micro controllers in the history, 8051

Get  30%  free preview inside our course to see how each lecture is broken down, how we teach, and whether or not you think we’re a good fit for you and your company.

I believe that any one can learn and experiment with technology.

All that is needed is desire to learn and right guidance.  That’s the reason, this course is focused to both 

  • absolute beginners and 

  • intermediate developers in embedded systems. 

We’re going to study about embedded systems with 8051 microcontroller in this course.

8051 is by far one of the oldest micro controllers which is still used today. With over 70+ different manufacturers, 8051 is available in a variety of flavours. What makes it special is the simplicity it offers to the programmers and developers. Being one of the first micro controllers, the architecture of 8051 is quite simple with very few basic features. And those very basic features make 8051 the winner in terms of simplicity in usage.

In this course, we’ll study 8051 with embedded C programming. We’re going to study about the 8051 microcontrollers with Keil 8051 IDE. Keil microvision is a very old and very popular IDE used for microcontroller programming.

This is a hands-on driven course where we’ll be writing a lot of codes and trying out its outputs. We’re going to study 8051 microcontroller and its interfacing with number of peripheral devices like

  • LEDS

  • Switches

  • Relay

  • LCD

  • ADC

  • Temperature Sensor

  • Stepper Motor

  • DC Motor

  • PC Interfacing

  • Device Control

And while doing so, we’ll be doing number of different experiments to evaluate the skills we have been learning. The course outcome is to enable everyone to be able to use 8051 microcontroller and start creating projects on it.

Even if you do not know any C programming before, do not worry, there’s a brief introduction on C programming also.

This course comes from a developer

From past 10 years, I've developed more than 150 projects on 8051 micro controllers alone. This course doesn't come from a trainer following a set syllabus, this comes from a real developer who's involved in real projects for better part of his career. So there are many practical considerations mentioned time to time in this course.

Barebone Controller Coding

Programming and using a microcontroller is not like using Arduino’s where you just write C code and download into IC. This is a barebone coding experience where we’re going to learn the insights of 8051 microcontroller and understand at the core how to write program for each of its feature. This single quality separates the hobbyists and professionals apart. If you’ve once understood how to go into the microcontrollers features, look into registers and configure them to use, then you’ve understood the holy grail of embedded systems development. We’re going to do exactly this in this course. We’ll be using each feature of 8051 by completely studying the internal registers. Once you’ve understood it, you can take any microcontroller and start writing program for it just by looking into the datasheet. The input / output pins, timers, counters, serial port, are discussed at length to understand the theory better and then we’ve done some quick experiments with it on the go.

Simulations

Many of you may or may not have 8051 development board with you, hence, I’ve included simulation models of every single exercise that we’re going to do in this course. And I’ve also shown the downloading procedure for one of the simplest microcontrollers that I use on daily basis.

Be Assured

Believe it or not, am doing embedded systems development and training from past 10 years. I’ve developed more than 500 different products / mini projects and trained more than 10000 students from over 65 countries. You can be assured that whatever I’ve included in this course comes not only from book but also from my experiences in developing systems.

Test Drive it

Take the free preview before enrolling the course, 25% of the course is free for you. Decide if it’s good for you or not even before enrolling. See and decide if you can understand and cope up with the content and the presenter of the course!!!

Enroll now and start experimenting!!!


 Who this course is for: 
  • Beginner, Students who are curious to learn Micro controller Programming
  • College and University students
  • Working Professionals willing to start studying embedded systems

What's included?

Video Icon 33 videos File Icon 12 files Text Icon 2 text files

Contents

Introduction
Introduction to Course
3 mins
Introduction to Embedded Systems
20 mins
Introduction To 8051 Microcontroller Pin Structure
15 mins
Program for 8051
13 mins
Software Installation
Installation of Keil IDE
6 mins
First Project creation on Kiel
6 mins
Simulations
Input and Output Interfacing
Concepts on LED
13 mins
Project based on Led Alternate on off
5 mins
Using For Loop
6 mins
led_codes.zip
142 KB
8051 Interfaces
Switch Interfacing with 8051
13 mins
Switch Exercises
switchCodes.zip
309 KB
Interfacing with DC Motor and Relay
Relay Interfacing Part 1
11 mins
relayPort.zip
65.9 KB
Downloadable
65.9 KB
Relay Interfacing Part 2
3 mins
Introduction To DC Motor
10 mins
DC Motor Interfacing Part 2
7 mins
L293 Interfacing.zip
81.3 KB
Concepts On LCD
Introduction To LCD
9 mins
Creating Schematics for LCD
8 mins
Fisrt Program On LCD
7 mins
LCD_interfacing.zip
189 KB
21.LCD-Interfacing-4.mp4
9 mins
LCD 4 bit library.zip
55.2 KB
Concepts On Serial
Serial_1
8 mins
Serial_2
14 mins
Serial_3
8 mins
Serial_4
8 mins
SerialTestCodes.zip
34.5 KB
Timer Concepts
Timer_1
8 mins
Timer_2
7 mins
Timer_3
6 mins
timer delay codes.zip
145 KB
Timer as Counter
29.Final Timer as Counter.mp4
8 mins
Timer as Counter.zip
88.3 KB
ADC With LM35
Analog to Digital Converter with 8051 - Part 1
10 mins
Analog to Digital Converter with 8051 - Part 2
7 mins
Analog to Digital Converter with 8051 - Part 3
10 mins
Analog to Digital Converter with 8051 use LM35 Temperature Sensor
11 mins
adc Codes.zip
131 KB
Stepper Motor and Program for Stepper Motor
Concepts around Stepper Motor
15 mins
stepper codes.zip
133 KB
Program Downloading
35.Program Downloading Using Nuvoton.mp4
9 mins
Conclusion
36.Conclusion Final.mp4
1 min